Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 5 - Jul 10
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Syvecs AWD Module / Haldex Controller for Audi S3 (8V) & VW Golf R (7.1 / 7.5)Syvecs Haldex Controller Fitment: Audi S3 (8V) & VW Golf R (7. 1 7. 5) The Syvecs MQB AWD module is a standalone AWD 4WD Centre Diff controller designed to control the Haldex system in the VAG group 4 Cylinder MQB cars. This includes the following and more. Audi S3 Seat Leon Cupra VW Golf R7. 1 VW Golf R7. 5 Please note this unit will not work with the RS3 TTRS, You will require the Special Controller from IROZ Motorsport for this. Please see the
Syvecs Haldex Controller
Fitment: Audi S3 (8V) & VW Golf R (7.1 / 7.5)
The Syvecs MQB AWD module is a standalone AWD/4WD/Centre Diff controller designed to control the Haldex system in the VAG group 4 Cylinder MQB cars. This includes the following and more.
Audi S3
Seat Leon Cupra
VW Golf R7.1
VW Golf R7.5
Please note this unit will not work with the RS3/TTRS, You will require the Special Controller from IROZ Motorsport for this. Please see the dedicated product page for the RS3/TTRS AWD Module
The OEM haldex controller are locked down and not adjustable, but by simply fitting our AWD Module a whole new level of control is available. The unit allows users to optimize control and provide the best performance available from the powertrain.
The MQB version of the controller replicates all the OEM CAN information as well as pick up lots of variable from the OEM Can to link into the control strategies like Steering Angle, Brake Pressure, Rpm, Tps, Lateral G, Yaw, Long G, Speeds, Temperatures and mode switches
Limp Protection options for large slip, high current, high temps which warn the driver but keep AWD active unlike the OEM controllers which shut down the outputs which is not ideal with high horsepower!
Works with any Engine management system
The Drive Mode Button on the MQB is used for Map switching so allows users to be able to change between AWD Select 1, 2, 3 which means all the maps below can be adjusted. You can also enable the burnout mode to be active when Hazards are on or if handbrake is present.
With the use of our SCAL Software, users can connect to the Device and adjust over 40 maps to adjust the control of the solenoids/motors used in the AWD systems.
Live adjustment potentiometers which gives drivers the ability to adjust the AWD Duty on the move or go 2wd from the flick of a switch.
Some of the Maps available
4 x Base Duty Tables
4 x Adders with enable maps:
Left Foot Braking
Front Slip
Rear Slip
Centre Slip
4 x Multipliers with enable maps
Steering Angle
AWD Temp
AWD Pressure
AWD Potentiometer
Tire Diameter adjustment under sensors
2WD/ Burnout Mode
Via Dedication Switched input
Via Can bus Message
Via OEM Functions
Limiters
Maximum Duty
Launch Control Limit
Duty Rate of Change
Decay/Hold Functions
Limp Mode
Over Current Protection
Over Slip Protection
Over Temp Protection
Cooling Pump control
AWD Cooling pump control logic
Datastream
The Syvecs AWD Unit also has a dedicated Can bus transmit area where users can send variables from the AWD to external control units for monitoring or to OEM CanBus system via custom Identifiers and byte structuring
Sensors / Switches
External sensors can be connected to the AWD module and then linearized in our SCAL Software
Maximum of 30 Amps via pin sharing (HBR1&2 or HBR3&4)
Onboard Current Monitoring of each output
2 x CanBus - Configurable Transmit Via SCAL Program
4 x Analog inputs for assigning Burnout Switch, Adjustment Pot, Pressure sensor and Temp sensor.
4 x Magneto Resistive ABS Sensor Inputs for direct Speed monitoring
USB Connection - Dedicated SCAL software with full calibration control
VCDS Support - Communicates with OEM Tools and Replicates OEM Haldex Ecu's
Mains Power control circuit based from Ignition Switch
Reverse Polarity Protection
Weatherproof Enclosure
125c Temperature capable
6v to 25v capable
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy