Arduino Nano RP2040 Connect with headers ABX00053

Product description:

Arduino Nano RP2040 Connect with connectors - ABX00053

Another module from the series Arduino Nano. This is the first Arduino board created in cooperation with Raspberry Pi. Arduino Nano RP2040 Connect module is based on chip Raspberry Pi RP2040and it's the first module which combines this chip with additional sensors and connectivity on one PCB. The board houses the aforementioned RP2040 chip, a6-axis sensor IMU, a U-Blox Nina chip for Wi-Fi and Bluetooth communication, as well as a microphone and an RGB LED. The IMU chip has machine learning capability, so additional sensing algorithms are available. The terminals of the Arduino Nano RP2040 Connect module operate at 3.3V. This version has soldered pins.

Main features of the Arduino Nano RP2040

• Interfaces: USB, SPI, I2C, I2S, UART, PWM
  
• U-Blox Nina chip for Wi-Fi / Bluetooth wireless communication
  
• Micro-USB connector for computer connection and 5V power supply
  
• Built-in microphone, RGB LED and 6-axis IMU
  
• Based on Raspberry Pi RP2040 microcontroller clocked at 133 MHz
  
• Built-in 16MB Flash memory and 264kB SRAM
  
• 20 PWM pins, 8 analog pins and 22 digital pins
  
• Standard dimensions for Nano series - 45 x 18 mm

ARDUINO NANO RP2040 CONNECT SPECIFICATIONS

• Power supply voltage: 4.5V to 21V
  
• Operating voltage of logic part: 3.3V
  
• Output current 3.3V: 800 mA
  
• RP2040 microcontroller
  
• ARM Cortex M0 Dual-Core 133 MHz
  
• 264 kB SRAM
  
• 2 MB Flash
  
• DMA controller
  
• Supports up to 16 MB Flash memory via QSPI bus
  
• Programmable IO (PIO) to support external peripherals
  
• 4-channel ADC with internal temperature sensor, 0.5 MSa/s, 12-bit conversion
  
• SWD debugging
  
• Wi-Fi / Bluetooth module: U-blox Nina W102
  
• dual core Xtensa LX6 240 MHz 32-bit
  
• 520 kB SARAM on-chip memory
  
• 448 kB ROM for boot and core functions
  
• 16 MB Flash memory for code storage, includes hardware encryption for program and data protection
  
• 1 kB EFUSE for MAC address, module configuration, Flash encryption and Chip-ID
  
• IEEE 802.11 b/g/n 2.4 GHz WiFi
  
• Bluetooth 4.2
  
• Built-in antenna (PIFA)
  
• 4 x 12-bit ADC
  
• 3 x I2C, SDIO, CAN, QSPI
  
• Memory: AT25SF128A 16MB NOR Flash | 532 Mb/s QSPI data transfer
  
• 100k programming / erase cycles
  
• Sensor IMU: 6-axis ST LSM6DSOXTR
  
• 3D gyroscope: ± 2 / ± 4 / ± 8 / ± 16 g full scale
  
• 3D accelerometer: ± 125 / ± 250 / ± 500 / ± 1000 / ± 2000 dps full scale 
• Advanced pedometer, step detector and step counter
  
• Motion detection and roll detection
  
• Standard interrupts: free fall, 6D/4D orientation wake-up, click, double click
  
• Programmable finite state machine: accelerometer, gyroscope and external sensors
  
• Machine learning core
  
• Embedded temperature sensor
  
• MEMS ST microphone MP34DT06JTR
  
• AOP = 122.5 dBSPL
  
• Signal to noise ratio: 64 dB
  
• Omnidirectional sensitivity
  
• Frequency: -26 dBFS ± 1 dB
  
• RGB LED
  
• Common anode
  
• Connected to U-blox Nina W102 GPIO
  
• Microchip: ATECC608A cryptographic chip cryptographic coprocessor with secure hardware key storage
  
• I2C, SWI Hardware support for symmetric algorithms: SHA-256 and HMAC HASH including off-chip context saving/restoration